Zipper factory tutor life tips: zipper head off how to put it back

In real life, we often encounter situations where the zipper head is pulled down. How to put the chain head back when it is lost? The following zipper manufacturers bring you zipper maintenance methods and other related knowledge.

Zipper heads are a common occurrence in daily life, so how to pull them back when they are lost? The following editor brings you illustrations, zipper cardboard, zipper maintenance and other related knowledge.

How to put the zipper back when it falls off?

1. After cutting the lighter, burn off the edges to prevent detachment.

2. Pull the zipper head into the teeth in an upward direction. Pull the two ends of the tape (arrow position) together and pull outward (as shown in the figure). The zipper will follow the tension of the tape. Entering the teeth.

After pulling out the fabric, the slider has been installed.

4. Use diagonal pliers to extract excess teeth.

5. Install up and down.

The above is a detailed explanation of how zipper manufacturers pay attention to the wear of zipper heads.

Tips for handling zipper to clothing

You may encounter situations where the zipper gets stuck on the high imitation clothing fabric when pulled and cannot be moved or moved. Do not use brute force to pull hard at this time, otherwise it will become even tighter. You should slowly pull out the fabric stuck in the slider, then pull the slider back to its original position and slowly pull it up. Be patient and handle it!

When using zipper technology, you should pay attention to the zipper, such as breaking the belly, removing teeth, and skewing. If the zipper is loose and has teeth, you can use a small hammer to lightly tap the zipper head a few times to make the upper and lower teeth bite tightly, and you won't have to remove the teeth again.

Do not fill various bags, pockets, or wallets with zippers. When pulling the zipper, first align the teeth on both sides, then pinch the zipper head and gently pull it forward along the track without pulling too hard.

Zipper maintenance techniques

1. During normal use, please pay attention to issues such as abdominal detachment, tooth extraction, and skewing on the zipper. If you encounter these problems, please repair them promptly and do not pull or tug forcefully. If the zipper is loose and has teeth, use a small hammer to lightly tap the zipper head a few times to make the upper and lower chain teeth bite tightly, and then do not remove the teeth again.

2. Aluminum alloy zippers are more prone to corrosion, so they should be kept dry and not damp to prevent the formation of white oxides on the aluminum teeth, which can cause the zipper to rust and affect its long-term use. However, it is also important to avoid contact with alkaline substances. During storage, it should be kept well ventilated and not sealed. Do not store it in a damp environment or use moisture-proof paper or dehumidifier if necessary. If the zipper is damp and pulled up, dry it in the sun, apply some wax to the teeth of the zipper, and then fire it to make it very smooth.

When pulling the zipper, first align the teeth on both sides, then pinch the zipper head and gently pull it forward along the track. Do not pull it forcefully to avoid crooked, broken, and dislocated teeth. If the zipper is a bun and the tension is not flexible, you can wipe it with a cloth and then apply a layer of white wax on the teeth.

4. Various bags, pockets, or zippered wallets should not be overfilled, otherwise it is easy for the zipper to break the abdomen, teeth to protrude, tilt, and the fabric to become soft.

Zipper repair method

If the iron edges on both sides of the zipper come off. Repair instructions: You can fold one end of the staple inward, making it parallel to the iron, and straighten the other end. Cut off the excess part of the nail from the straight end according to the length of the zipper iron edge. After cutting, the staple should be placed on the original iron edge. The folded back is placed below, flush with the bottom edge of the zipper, and the other end is folded to the same point. Then sew the two pieces back and forth tightly with a windbreaker needle, and wrap the staples inside, with a width equal to the original iron edge; The bottom edge of the book nail should be tightly pulled onto the seam, the seam should be smooth, and then touched with wax. In an instant, the maintenance effect is the same as the original iron edge.

If the zipper is missing teeth. Maintenance method introduction: At the original tail end, use a pointed nose or camera to open the zipper teeth and remove a few teeth. After installing the teeth removal component, gently press the tooth opening onto the edge of the cloth with a pointed tip. He can only bite people.

Sometimes the zipper cannot be pulled or pulled to the middle because the teeth of the zipper are broken or the fibers of the tape are loose. If the teeth of the zipper are broken, you can use a steel needle to straighten it, then flatten it, and gently flatten the zipper teeth with a small pair of tweezers. The zipper is ready. If the tape is loose, you can pull the mismatched tape and evenly arrange the teeth of the zipper, you can pull them.

There are two reasons why zippers are not smooth: they are good, but the teeth are rusty or contaminated with dirt; Secondly, the handle foot is clamped at the edge of the fabric, etc. The former can slide smoothly and freely by gently wiping both sides of the zipper with wax; The latter should slowly return the key head to its original position and remove foreign objects. The zipper should not be close to the monitor, as the distance between the upper and lower parts of the zipper head can be changed by Jiangda or simply clamped up and down or left and right with pliers, but be careful not to use too much force to avoid pinching.

If the zipper lock is disconnected, only the zipper lock can be replaced.

6. If there is no damage, please follow the steps below: First, use pliers to pull down the large teeth at the top of the zipper and move them on both sides; Then pull the zipper latch to the top; Then bring the two teeth together; Then lock the zipper into it (with some difficulty because the diameter of the metal zipper is relatively thick. If it is not set, cut a small hole on the line. Remember not to cut it at its place to install the large teeth, but to cut it at the top, otherwise the large teeth cannot be installed); Afterwards, zip up and place the large teeth on top.

7. Zipper Slippery Tip: Zippers are damp or rusty, and they may not be able to be pulled smoothly after oxidation. When not pulled, use force, such as wiping back and forth with candles on two rows of teeth and putting on barbecue fire once. When pulled, they will be very smooth.

If the zipper is pulled, it will open on its own: this problem is because the puller has been pulling for too long and the diameter is getting larger and larger. If you want to temporarily solve it, please use pliers to clamp the tail of the puller. Just pay attention to the tail, but be careful not to use too much force or pinch it. If you want to completely solve it, you need to replace the slider. This article is compiled and collected by zipper manufacturer www.baerman.cn and does not represent the views of our website. If you would like to learn more about zippers, please click to view other articles on waterproof zippers, resin zippers, and invisible zippers. Please follow Zipper website